FSP Configuration
  Board "RA2|RA2L1|VOICE-RA2L1"
  R7FA2L1AB3CFL
    part_number: R7FA2L1AB3CFL
    rom_size_bytes: 262144
    ram_size_bytes: 32768
    data_flash_size_bytes: 8192
    package_style: LQFP
    package_pins: 48
    number of cores: 1
    
  R7FA2L1AB3CFL
  RA2L1
    series: 2
    
  RA2L1 Family
    Enable inline BSP IRQ functions: Disabled
    Use Low Voltage Mode: Not Supported
    Power: DC-DC Regulator: Disabled
    Power: DC-DC Supply Range: 2.7V to 3.6V
    Main Oscillator Wait Time: 262144 cycles
    
  RA2L1 Device Options
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: Enabled
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: Independent WDT: Start Mode: IWDT is stopped after a reset
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: Independent WDT: Timeout Period: 2048 cycles
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: Independent WDT: Dedicated Clock Frequency Divisor: 128
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: Independent WDT: Window End Position:  0% (no window end position)
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: Independent WDT: Window Start Position: 100% (no window start position)
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: Independent WDT: Reset Interrupt Request Select: Reset is enabled
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: Independent WDT: Stop Control: Stop counting when in Sleep,Snooze modec, or Software Standby
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: WDT: Start Mode Select: Stop WDT after a reset (register-start mode)
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: WDT: Timeout Period: 16384 cycles
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: WDT: Clock Frequency Division Ratio: 128
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: WDT: Window End Position:  0% (no window end position)
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: WDT: Window Start Position: 100% (no window start position)
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: WDT: Reset Interrupt Request: Reset
    OFS Registers: OFS0 (Option Function Select Register 0) Settings: WDT: Stop Control: Stop counting when entering Sleep mode
    OFS Registers: OFS1 (Option Function Select Register 1) Settings: Enabled
    OFS Registers: OFS1 (Option Function Select Register 1) Settings: Voltage Detection 0 Circuit Start: Voltage monitor 0 reset is disabled after reset
    OFS Registers: OFS1 (Option Function Select Register 1) Settings: Voltage Detection 0 Level: 1.90 V
    OFS Registers: OFS1 (Option Function Select Register 1) Settings: HOCO Oscillation Enable: HOCO oscillation is disabled after reset
    OFS Registers: OFS1 (Option Function Select Register 1) Settings: Internal Clock Supply Architecture Type: Type A
    OFS Registers: SECMPU (Security MPU Registers) Settings: Disabled
    OFS Registers: SECMPU (Security MPU Registers) Settings: PC 0 Enable: Disabled
    OFS Registers: SECMPU (Security MPU Registers) Settings: PC 0 Start: 0x0003FFFC
    OFS Registers: SECMPU (Security MPU Registers) Settings: PC 0 End: 0x0003FFFF
    OFS Registers: SECMPU (Security MPU Registers) Settings: PC 1 Enable: Disabled
    OFS Registers: SECMPU (Security MPU Registers) Settings: PC 1 Start: 0x0003FFFC
    OFS Registers: SECMPU (Security MPU Registers) Settings: PC 1 End: 0x0003FFFF
    OFS Registers: SECMPU (Security MPU Registers) Settings: Region 0 Enable: Disabled
    OFS Registers: SECMPU (Security MPU Registers) Settings: Region 0 Start: 0x0003FFFC
    OFS Registers: SECMPU (Security MPU Registers) Settings: Region 0 End: 0x0003FFFF
    OFS Registers: SECMPU (Security MPU Registers) Settings: Region 1 Enable: Disabled
    OFS Registers: SECMPU (Security MPU Registers) Settings: Region 1 Start: 0x20007FFC
    OFS Registers: SECMPU (Security MPU Registers) Settings: Region 1 End: 0x20007FFF
    OFS Registers: SECMPU (Security MPU Registers) Settings: Region 2 Enable: Disabled
    OFS Registers: SECMPU (Security MPU Registers) Settings: Region 2 Start: 0x400DFFFC
    OFS Registers: SECMPU (Security MPU Registers) Settings: Region 2 End: 0x400DFFFF
    OFS Registers: SECMPU (Security MPU Registers) Settings: Region 3 Enable: Disabled
    OFS Registers: SECMPU (Security MPU Registers) Settings: Region 3 Start: 0x400DFFFC
    OFS Registers: SECMPU (Security MPU Registers) Settings: Region 3 End: 0x400DFFFF
    OFS Registers: OSIS (OCD/Serial Programmer ID setting register) Settings: Disabled
    OFS Registers: OSIS (OCD/Serial Programmer ID setting register) Settings: ID Code Mode: Unlocked (Ignore ID)
    OFS Registers: OSIS (OCD/Serial Programmer ID setting register) Settings: ID Code (32 Hex Characters): FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
    
  RA2L1 event data
  RA Common
    Main stack size (bytes): 2816
    Heap size (bytes): 256
    Bootloader Secondary XIP: Disabled
    MCU Vcc (mV): 3300
    Parameter checking: Disabled
    Assert Failures: Return FSP_ERR_ASSERTION
    Clock Registers not Reset Values during Startup: Disabled
    Main Oscillator Populated: Not Populated
    PFS Protect: Enabled
    C Runtime Initialization : Enabled
    Early BSP Initialization : Disabled
    Main Oscillator Clock Source: Crystal or Resonator
    Subclock Populated: Not Populated
    Subclock Drive (Drive capacitance availability varies by MCU): Standard/Normal mode
    Subclock Stabilization Time (ms): 1000
    
  Clocks
    XTAL 20000000Hz
    HOCO 48MHz
    Clock Src: HOCO
    ICLK Div /1
    PCLKB Div /2
    PCLKD Div /1
    CLKOUT Disabled
    CLKOUT Div /1
    
  Pin Configurations
    R7FA2L1AB3CFL.pincfg -> g_bsp_pin_cfg
      AVCC0 42 ANALOG0_AVCC0 - - - - - - - - IO "Read only" - 
      AVSS0 43 ANALOG0_AVSS0 - - - - - - - - IO "Read only" - 
      P000 48 ADC0_AN000 - - - "Analog mode" - None "ADC0: AN000; CTSU0: TS21; ICU0: IRQ06" AMIC_L IO - - 
      P001 47 ADC0_AN001 - - - "Analog mode" - None "ADC0: AN001; CTSU0: TS22; ICU0: IRQ07" AMIC_R IO - - 
      P002 46 ADC0_AN002 - - - "Analog mode" - - "ADC0: AN002; CTSU0: TS23; ICU0: IRQ02" TP11 None - - 
      P010 45 - - - - Disabled - - "ADC0: AN005; ANALOG0: VREFH0; CTSU0: TS30-CFC" - None - - 
      P011 44 - - - - Disabled - - "ADC0: AN006; ANALOG0: VREFL0; CTSU0: TS31-CFC" - None - - 
      P012 41 ADC0_AN007 - - - "Analog mode" - - "ADC0: AN007; CTSU0: TS32-CFC" TP12 None - - 
      P013 40 - - - - Disabled - - "ADC0: AN008; CTSU0: TS33-CFC" TP13 None - - 
      P014 39 DAC0_DA0 - - - "Analog mode" - None "ADC0: AN009; DAC0: DA0" PLAYBACK IO - - 
      P015 38 GPIO - - - "Input mode" - - "ADC0: AN010; CTSU0: TS28-CFC; ICU0: IRQ07" TP14 None - - 
      P100 36 - - - None Disabled CMOS None "ACMPLP0: CMPIN0; AGT0: AGTIO0; CTSU0: TS26-CFC; GPT_POEG0: GTETRGA; GPT5: GTIOC5B; ICU0: IRQ02; IIC1: SCL1; KINT0: KRM00; SCI0: RXD0; SCI0: SCL0; SCI1: SCK1; SPI0: MISOA" "SCK_OUT (as I2S SCK)" IO - - 
      P101 35 SPI0_MOSIA - - None "Peripheral mode" CMOS None "ACMPLP0: CMPREF0; AGT0: AGTEE0; CTSU0: TS16-CFC; GPT_POEG1: GTETRGB; GPT5: GTIOC5A; ICU0: IRQ01; IIC1: SDA1; KINT0: KRM01; SCI0: SDA0; SCI0: TXD0; SCI1: CTS1; SPI0: MOSIA" "SPI0 MOSI" IO - - 
      P102 34 SPI0_RSPCKA - - - "Peripheral mode" CMOS None "ACMPLP1: CMPIN1; ADC0: ADTRG0; AGT0: AGTO0; CAN0: CRX0; CTSU0: TS15-CFC; GPT_OPS0: GTOWLO; GPT2: GTIOC2B; KINT0: KRM02; SCI0: SCK0; SCI2: SDA2; SCI2: TXD2; SPI0: RSPCKA" "SPI0 SCK" IO - - 
      P103 33 SPI0_SSLA0 - - - "Peripheral mode" CMOS None "ACMPLP1: CMPREF1; CAN0: CTX0; CTSU0: TS14-CFC; GPT_OPS0: GTOWUP; GPT2: GTIOC2A; KINT0: KRM03; SCI0: CTS0; SPI0: SSLA0" "SPI0 SSL" IO - - 
      P104 32 GPT_POEG1_GTETRGB - - None "Peripheral mode" CMOS None "CTSU0: TS13-CFC; GPT_POEG1: GTETRGB; GPT1: GTIOC1B; ICU0: IRQ01; KINT0: KRM04; SCI0: RXD0; SCI0: SCL0; SPI0: SSLA1" POEG1 IO - - 
      P108 25 DEBUG0_SWDIO - - - "Peripheral mode" - None "DEBUG0: SWDIO; GPT_OPS0: GTOULO; GPT0: GTIOC0B; SCI9: CTS9; SPI1: SSLB0" - IO - - 
      P109 26 GPIO - - - "Output mode (Initial Low)" CMOS None "CAN0: CTX0; CGC0: CLKOUT; CTSU0: TS10-CFC; GPT_OPS0: GTOVUP; GPT1: GTIOC1A; SCI1: SCK1; SCI9: SDA9; SCI9: TXD9; SPI1: MOSIB" "PMOD MOSI/TXD/NC" IO - - 
      P110 27 GPIO - - IRQ03 "Input mode" CMOS "input pull-up" "ACMP(0-1): VCOUT; CAN0: CRX0; CTSU0: TS11-CFC; GPT_OPS0: GTOVLO; GPT1: GTIOC1B; ICU0: IRQ03; SCI2: CTS2; SCI9: RXD9; SCI9: SCL9; SPI1: MISOB" "PMOD MISO/RXD/SCL" IO - - 
      P111 28 GPIO - - None "Output mode (Initial Low)" CMOS None "AGT0: AGTOA0; CTSU0: TS12-CFC; GPT3: GTIOC3A; ICU0: IRQ04; SCI2: SCK2; SCI9: SCK9; SPI1: RSPCKB" "PMOD SCK/RTS/SDA" IO - - 
      P112 29 GPIO - - - "Output mode (Initial Low)" CMOS None "AGT0: AGTOB0; CTSU0: TSCAP; GPT3: GTIOC3B; SCI1: SCK1; SCI2: SDA2; SCI2: TXD2; SPI1: SSLB0" "I2S WS Delay for SPI SSL" IO - - 
      P200 21 - - - - Disabled - - "ICU0: NMI" - None - - 
      P201 20 - - - - Disabled - - "SYSTEM0: MD" - None - - 
      P206 18 GPIO - - None "Output mode (Initial Low)" CMOS - "GPT_OPS0: GTIU; ICU0: IRQ00; IIC1: SDA1; SCI0: RXD0; SCI0: SCL0; SPI1: SSLB1" "PMOD IO1" IO - - 
      P207 17 GPIO - - - "Output mode (Initial Low)" CMOS - - "PMOD IO2" IO - - 
      P208 16 GPIO - - - "Output mode (Initial Low)" CMOS - "AGT0: AGTOB0" "PMOD IO3" IO - - 
      P212 8 GPIO - - None "Output mode (Initial High)" CMOS - "AGT1: AGTEE1; CGC0: EXTAL; GPT_POEG1: GTETRGB; GPT0: GTIOC0B; ICU0: IRQ03; SCI1: RXD1; SCI1: SCL1" LED3 IO - - 
      P213 7 GPIO - - None "Output mode (Initial High)" CMOS - "CGC0: XTAL; GPT_POEG0: GTETRGA; GPT0: GTIOC0A; ICU0: IRQ02; SCI1: SDA1; SCI1: TXD1" LED2 IO - - 
      P214 5 - - - - Disabled - - "CGC0: XCOUT" - IO - - 
      P215 4 - - - - Disabled - - "CGC0: XCIN" - IO - - 
      P300 24 DEBUG0_SWCLK - - - "Peripheral mode" - None "DEBUG0: SWCLK; GPT_OPS0: GTOUUP; GPT0: GTIOC0A; SPI1: SSLB1" - IO - - 
      P301 23 SCI2_RXD2 - - None "Peripheral mode" CMOS - "AGT0: AGTIO0; CTSU0: TS09-CFC; GPT_OPS0: GTOULO; GPT4: GTIOC4B; ICU0: IRQ06; SCI2: RXD2; SCI2: SCL2; SCI9: CTS9; SPI1: SSLB2" "PMOD SS/CTS/NC" IO - - 
      P302 22 SCI2_TXD2 - - None "Peripheral mode" - None "CTSU0: TS08-CFC; GPT_OPS0: GTOUUP; GPT4: GTIOC4A; ICU0: IRQ05; SCI2: SDA2; SCI2: TXD2; SPI1: SSLB3" "PMOD IRQ" IO - - 
      P400 1 - - - None Disabled - None "AGT1: AGTIO1; CAC0: CACREF; GPT6: GTIOC6A; ICU0: IRQ00; IIC0: SCL0; SCI0: SCK0; SCI1: SCK1" "USER SW" IO - - 
      P401 2 - - - None Disabled CMOS None "CAN0: CTX0; GPT_POEG0: GTETRGA; GPT6: GTIOC6B; ICU0: IRQ05; IIC0: SDA0; SCI0: CTS0; SCI1: SDA1; SCI1: TXD1" "I2S WS" IO - - 
      P407 12 IIC0_SDA0 - - - "Peripheral mode" - - "ADC0: ADTRG0; AGT0: AGTIO0; IIC0: SDA0; RTC0: RTCOUT; SCI0: CTS0; SPI1: SSLB3" TP10 None - - 
      P408 11 IIC0_SCL0 - - None "Peripheral mode" CMOS None "CTSU0: TS04; GPT_OPS0: GTOWLO; GPT5: GTIOC5B; ICU0: IRQ07; IIC0: SCL0; SCI1: CTS1; SCI3: RXD3; SCI3: SCL3" "SCI RXD for USB VCOM" IO - - 
      P409 10 GPIO - - IRQ06 "Input mode" CMOS "input pull-up" "CTSU0: TS05; GPT_OPS0: GTOWUP; GPT5: GTIOC5A; ICU0: IRQ06; SCI3: SDA3; SCI3: TXD3" "SCI TXD for USB VCOM" IO - - 
      P500 37 GPIO - - - "Output mode (Initial High)" CMOS - "GPT_OPS0: GTIU; GPT2: GTIOC2A" LED1 IO - - 
      RES# 19 SYSTEM0_RES - - - - - - - - IO "Read only" - 
      VCC 9 SYSTEM0_VCC - - - - - - - - IO "Read only" - 
      VCC 30 SYSTEM0_VCC - - - - - - - - IO "Read only" - 
      VCCDCDC 15 SYSTEM0_VCC_DCDC - - - - - - - - IO "Read only" - 
      VCL 3 SYSTEM0_VCL - - - - - - - - IO "Read only" - 
      VLO 14 SYSTEM0_VLO - - - - - - - - IO "Read only" - 
      VSS 6 SYSTEM0_VSS - - - - - - - - IO "Read only" - 
      VSS 31 SYSTEM0_VSS - - - - - - - - IO "Read only" - 
      VSSDCDC 13 SYSTEM0_VSS_DCDC - - - - - - - - IO "Read only" - 
    VOICE_RA2L1 -> g_bsp_pin_cfg
      AVCC0 42 ANALOG0_AVCC0 - - - - - - - - IO "Read only" - 
      AVSS0 43 ANALOG0_AVSS0 - - - - - - - - IO "Read only" - 
      P000 48 ADC0_AN000 - - - "Analog mode" - None "ADC0: AN000; CTSU0: TS21; ICU0: IRQ06" AMIC_L IO - - 
      P001 47 ADC0_AN001 - - - "Analog mode" - None "ADC0: AN001; CTSU0: TS22; ICU0: IRQ07" AMIC_R IO - - 
      P002 46 - - - - Disabled - - "ADC0: AN002; CTSU0: TS23; ICU0: IRQ02" TP11 None - - 
      P010 45 - - - - Disabled - - "ADC0: AN005; ANALOG0: VREFH0; CTSU0: TS30-CFC" - None - - 
      P011 44 - - - - Disabled - - "ADC0: AN006; ANALOG0: VREFL0; CTSU0: TS31-CFC" - None - - 
      P012 41 - - - - Disabled - - "ADC0: AN007; CTSU0: TS32-CFC" TP12 None - - 
      P013 40 - - - - Disabled - - "ADC0: AN008; CTSU0: TS33-CFC" TP13 None - - 
      P014 39 DAC0_DA0 - - - "Analog mode" - None "ADC0: AN009; DAC0: DA0" PLAYBACK IO - - 
      P015 38 - - - - Disabled - - "ADC0: AN010; CTSU0: TS28-CFC; ICU0: IRQ07" TP14 None - - 
      P100 36 GPT5_GTIOC5B - - None "Peripheral mode" CMOS None "ACMPLP0: CMPIN0; AGT0: AGTIO0; CTSU0: TS26-CFC; GPT_POEG0: GTETRGA; GPT5: GTIOC5B; ICU0: IRQ02; IIC1: SCL1; KINT0: KRM00; SCI0: RXD0; SCI0: SCL0; SCI1: SCK1; SPI0: MISOA" "SCK_OUT (as I2S SCK)" IO - - 
      P101 35 SPI0_MOSIA - - None "Peripheral mode" CMOS None "ACMPLP0: CMPREF0; AGT0: AGTEE0; CTSU0: TS16-CFC; GPT_POEG1: GTETRGB; GPT5: GTIOC5A; ICU0: IRQ01; IIC1: SDA1; KINT0: KRM01; SCI0: SDA0; SCI0: TXD0; SCI1: CTS1; SPI0: MOSIA" "SPI0 MOSI" IO - - 
      P102 34 SPI0_RSPCKA - - - "Peripheral mode" CMOS None "ACMPLP1: CMPIN1; ADC0: ADTRG0; AGT0: AGTO0; CAN0: CRX0; CTSU0: TS15-CFC; GPT_OPS0: GTOWLO; GPT2: GTIOC2B; KINT0: KRM02; SCI0: SCK0; SCI2: SDA2; SCI2: TXD2; SPI0: RSPCKA" "SPI0 SCK" IO - - 
      P103 33 SPI0_SSLA0 - - - "Peripheral mode" CMOS None "ACMPLP1: CMPREF1; CAN0: CTX0; CTSU0: TS14-CFC; GPT_OPS0: GTOWUP; GPT2: GTIOC2A; KINT0: KRM03; SCI0: CTS0; SPI0: SSLA0" "SPI0 SSL" IO - - 
      P104 32 GPT_POEG1_GTETRGB - - None "Peripheral mode" CMOS None "CTSU0: TS13-CFC; GPT_POEG1: GTETRGB; GPT1: GTIOC1B; ICU0: IRQ01; KINT0: KRM04; SCI0: RXD0; SCI0: SCL0; SPI0: SSLA1" POEG1 IO - - 
      P108 25 DEBUG0_SWDIO - - - "Peripheral mode" - None "DEBUG0: SWDIO; GPT_OPS0: GTOULO; GPT0: GTIOC0B; SCI9: CTS9; SPI1: SSLB0" - IO - - 
      P109 26 SCI9_TXD9 - - - "Peripheral mode" CMOS None "CAN0: CTX0; CGC0: CLKOUT; CTSU0: TS10-CFC; GPT_OPS0: GTOVUP; GPT1: GTIOC1A; SCI1: SCK1; SCI9: SDA9; SCI9: TXD9; SPI1: MOSIB" "PMOD MOSI/TXD/NC" IO - - 
      P110 27 SCI9_RXD9 - - None "Peripheral mode" CMOS None "ACMP(0-1): VCOUT; CAN0: CRX0; CTSU0: TS11-CFC; GPT_OPS0: GTOVLO; GPT1: GTIOC1B; ICU0: IRQ03; SCI2: CTS2; SCI9: RXD9; SCI9: SCL9; SPI1: MISOB" "PMOD MISO/RXD/SCL" IO - - 
      P111 28 SCI9_SCK9 - - None "Peripheral mode" CMOS None "AGT0: AGTOA0; CTSU0: TS12-CFC; GPT3: GTIOC3A; ICU0: IRQ04; SCI2: SCK2; SCI9: SCK9; SPI1: RSPCKB" "PMOD SCK/RTS/SDA" IO - - 
      P112 29 GPT3_GTIOC3B - - - "Peripheral mode" CMOS None "AGT0: AGTOB0; CTSU0: TSCAP; GPT3: GTIOC3B; SCI1: SCK1; SCI2: SDA2; SCI2: TXD2; SPI1: SSLB0" "I2S WS Delay for SPI SSL" IO - - 
      P200 21 - - - - Disabled - - "ICU0: NMI" - None - - 
      P201 20 - - - - Disabled - - "SYSTEM0: MD" - None - - 
      P206 18 GPIO - - None "Output mode (Initial Low)" CMOS - "GPT_OPS0: GTIU; ICU0: IRQ00; IIC1: SDA1; SCI0: RXD0; SCI0: SCL0; SPI1: SSLB1" "PMOD IO1" IO - - 
      P207 17 GPIO - - - "Output mode (Initial Low)" CMOS - - "PMOD IO2" IO - - 
      P208 16 GPIO - - - "Output mode (Initial Low)" CMOS - "AGT0: AGTOB0" "PMOD IO3" IO - - 
      P212 8 GPIO - - None "Output mode (Initial High)" CMOS - "AGT1: AGTEE1; CGC0: EXTAL; GPT_POEG1: GTETRGB; GPT0: GTIOC0B; ICU0: IRQ03; SCI1: RXD1; SCI1: SCL1" LED3 IO - - 
      P213 7 GPIO - - None "Output mode (Initial High)" CMOS - "CGC0: XTAL; GPT_POEG0: GTETRGA; GPT0: GTIOC0A; ICU0: IRQ02; SCI1: SDA1; SCI1: TXD1" LED2 IO - - 
      P214 5 CGC0_XCOUT - - - "Peripheral mode" - - "CGC0: XCOUT" - IO - - 
      P215 4 CGC0_XCIN - - - "Peripheral mode" - - "CGC0: XCIN" - IO - - 
      P300 24 DEBUG0_SWCLK - - - "Peripheral mode" - None "DEBUG0: SWCLK; GPT_OPS0: GTOUUP; GPT0: GTIOC0A; SPI1: SSLB1" - IO - - 
      P301 23 GPIO - - None "Output mode (Initial High)" CMOS - "AGT0: AGTIO0; CTSU0: TS09-CFC; GPT_OPS0: GTOULO; GPT4: GTIOC4B; ICU0: IRQ06; SCI2: RXD2; SCI2: SCL2; SCI9: CTS9; SPI1: SSLB2" "PMOD SS/CTS/NC" IO - - 
      P302 22 GPIO - - IRQ05 "Input mode" - None "CTSU0: TS08-CFC; GPT_OPS0: GTOUUP; GPT4: GTIOC4A; ICU0: IRQ05; SCI2: SDA2; SCI2: TXD2; SPI1: SSLB3" "PMOD IRQ" IO - - 
      P400 1 ICU0_IRQ00 - - IRQ00 "IRQ mode" - None "AGT1: AGTIO1; CAC0: CACREF; GPT6: GTIOC6A; ICU0: IRQ00; IIC0: SCL0; SCI0: SCK0; SCI1: SCK1" "USER SW" IO - - 
      P401 2 GPT6_GTIOC6B - - None "Peripheral mode" CMOS None "CAN0: CTX0; GPT_POEG0: GTETRGA; GPT6: GTIOC6B; ICU0: IRQ05; IIC0: SDA0; SCI0: CTS0; SCI1: SDA1; SCI1: TXD1" "I2S WS" IO - - 
      P407 12 - - - - Disabled - - "ADC0: ADTRG0; AGT0: AGTIO0; IIC0: SDA0; RTC0: RTCOUT; SCI0: CTS0; SPI1: SSLB3" TP10 None - - 
      P408 11 SCI3_RXD3 - - None "Peripheral mode" CMOS None "CTSU0: TS04; GPT_OPS0: GTOWLO; GPT5: GTIOC5B; ICU0: IRQ07; IIC0: SCL0; SCI1: CTS1; SCI3: RXD3; SCI3: SCL3" "SCI RXD for USB VCOM" IO - - 
      P409 10 SCI3_TXD3 - - None "Peripheral mode" CMOS None "CTSU0: TS05; GPT_OPS0: GTOWUP; GPT5: GTIOC5A; ICU0: IRQ06; SCI3: SDA3; SCI3: TXD3" "SCI TXD for USB VCOM" IO - - 
      P500 37 GPIO - - - "Output mode (Initial High)" CMOS - "GPT_OPS0: GTIU; GPT2: GTIOC2A" LED1 IO - - 
      RES# 19 SYSTEM0_RES - - - - - - - - IO "Read only" - 
      VCC 9 SYSTEM0_VCC - - - - - - - - IO "Read only" - 
      VCC 30 SYSTEM0_VCC - - - - - - - - IO "Read only" - 
      VCCDCDC 15 SYSTEM0_VCC_DCDC - - - - - - - - IO "Read only" - 
      VCL 3 SYSTEM0_VCL - - - - - - - - IO "Read only" - 
      VLO 14 SYSTEM0_VLO - - - - - - - - IO "Read only" - 
      VSS 6 SYSTEM0_VSS - - - - - - - - IO "Read only" - 
      VSS 31 SYSTEM0_VSS - - - - - - - - IO "Read only" - 
      VSSDCDC 13 SYSTEM0_VSS_DCDC - - - - - - - - IO "Read only" - 
    
  User Events
    LPM SNOOZE REQUEST (Snooze entry): user_def_isr_snz_req
    ADC0 COMPARE MATCH (Compare match): user_def_adc120_wcmpm
    ADC0 COMPARE MISMATCH (Compare mismatch): user_def_adc120_wcmpum
    
  User Event Links
    
  Linker Section Mappings
    *bsp_linker.?*(.rodata.*): FLASH Constant Data (OFS Gap)
    *startup.?*(.text.Reset_Handler): FLASH Code (OFS Gap)
    *system.?*(.text.*): FLASH Code (OFS Gap)
    *(.bss.g_heap): RAM Uninitialized
    *(.bss.g_main_stack): RAM Uninitialized
    
  Module "I/O Port (r_ioport)"
    Parameter Checking: Default (BSP)
    CCD Support: Not Supported
    
  Module "Timer, Low-Power (r_agt)"
    Parameter Checking: Default (BSP)
    Pin Output Support: Disabled
    Pin Input Support: Disabled
    
  Module "Low Power Modes (r_lpm)"
    Parameter Checking: Default (BSP)
    Standby Limit: Disabled
    
  Module "ADC (r_adc)"
    Parameter Checking: Default (BSP)
    
  Module "Event Link Controller (r_elc)"
    Parameter Checking: Default (BSP)
    
  Module "Transfer (r_dtc)"
    Parameter Checking: Default (BSP)
    Linker section to keep DTC vector table: .fsp_dtc_vector_table
    
  Module "Timer, General PWM (r_gpt)"
    Parameter Checking: Default (BSP)
    Pin Output Support: Enabled
    Write Protect Enable: Disabled
    
  Module "SPI (r_spi)"
    Parameter Checking: Default (BSP)
    Enable Support for using a transfer API: Enabled
    Enable Transmitting from RXI Interrupt: Disabled
    
  Module "Port Output Enable for GPT (r_poeg)"
    Parameter Checking: Default (BSP)
    
  Module "Flash (r_flash_lp)"
    Parameter Checking: Default (BSP)
    Code Flash Programming: Disabled
    Code Flash Background Operation Support With Bank Programming: Not Supported
    Data Flash Programming: Enabled
    Data Flash Background Operation Support: Enabled
    Instant Bank Swap (No Reset Required): Not Supported
    
  Module "UART (r_sci_uart)"
    Parameter Checking: Default (BSP)
    FIFO Support: Disable
    DTC Support: Disable
    Flow Control Support: Disable
    RS-485 Support: Disable
    IrDA Support: Disabled
    
  Module "DAC (r_dac)"
    Parameter Checking: Default (BSP)
    
  HAL
    Instance "g_ioport I/O Port (r_ioport)"
      Name: g_ioport
      1st Port ELC Trigger Source: Disabled
      2nd Port ELC Trigger Source: Disabled
      3rd Port ELC Trigger Source: Disabled
      4th Port ELC Trigger Source: Disabled
      Pin Configuration Name: g_bsp_pin_cfg
      
    Instance "g_agt1_lpm Timer, Low-Power (r_agt)"
      General: Name: g_agt1_lpm
      General: Counter Bit Width: AGT 16-bit
      General: Channel: 1
      General: Mode: Periodic
      General: Period: 10
      General: Period Unit: Milliseconds
      Output: Duty Cycle Percent (only applicable in PWM mode): 50
      General: Count Source: LOCO
      Output: AGTOA Output: Disabled
      Output: AGTOB Output: Disabled
      Output: AGTO Output: Disabled
      Input: Measurement Mode: Measure Disabled
      Input: Input Filter: No Filter
      Input: Enable Pin: Enable Pin Not Used
      Input: Trigger Edge: Trigger Edge Rising
      Interrupts: Callback: NULL
      Interrupts: Underflow Interrupt Priority: Disabled
      
    Instance "g_lpm0 Low Power Modes (r_lpm)"
      General: Name: g_lpm0
      General: Low Power Mode: Snooze mode
      General: Output port state in standby and deep standby: Not Supported
      General: Supply of SOSC clock to peripheral function in standby: Not Supported
      General: Startup speed of the HOCO in Standby and Snooze modes: Not Supported
      General: Flash mode in sleep or snooze: Not Supported
      Deep Sleep and Standby Options: Wake Sources: 
      Deep Sleep and Standby Options: Wake Sources 2: 
      Deep Sleep and Standby Options: Snooze Options (Not available on every MCU): Snooze Request Source: AGT1 Underflow
      Deep Sleep and Standby Options: Snooze Options (Not available on every MCU): Snooze End Sources: ADC0 Compare Mismatch
      Deep Sleep and Standby Options: Snooze Options (Not available on every MCU): DTC state in Snooze Mode: Disabled
      Deep Sleep and Standby Options: Snooze Options (Not available on every MCU): Snooze Cancel Source: ADC Unit 0 Compare Match
      RAM Retention Control (Not available on every MCU): RAM retention in Standby mode: 
      RAM Retention Control (Not available on every MCU): TCM retention in Deep Sleep and Standby modes: Not Supported
      RAM Retention Control (Not available on every MCU): Standby RAM retention in Standby and Deep Standby modes: Not Supported
      Oscillator LDO Control (Not available on every MCU): PLL1 LDO State in standby mode: Not Supported
      Oscillator LDO Control (Not available on every MCU): PLL2 LDO State in standby mode: Not Supported
      Oscillator LDO Control (Not available on every MCU): HOCO LDO State in standby mode: Not Supported
      Deep Standby Options (Not available on every MCU): I/O Port Retention: Not Supported
      Deep Standby Options (Not available on every MCU): Power-Supply Control: Not Supported
      Deep Standby Options (Not available on every MCU): Cancel Sources: 
      Deep Standby Options (Not available on every MCU): Cancel Edges: 
      Deep Standby Options (Not available on every MCU): Soft Start Mode: Not Available
      
    Instance "g_adc_lpm ADC (r_adc)"
      General: Name: g_adc_lpm
      General: Unit: 0
      General: Resolution: 12-Bit
      General: Alignment: Right
      General: Clear after read: Off
      General: Mode: Single Scan
      General: Double-trigger: Disabled
      Input: Channel Scan Mask (channel availability varies by MCU): Channel 0, Channel 1
      Input: Group B Scan Mask (channel availability varies by MCU): 
      Interrupts: Normal/Group A Trigger: AGT0 INT (AGT interrupt)
      Interrupts: Group B Trigger: Disabled
      Interrupts: Group Priority (Valid only in Group Scan Mode): Group A cannot interrupt Group B
      Input: Add/Average Count: Disabled
      Input: Reference Voltage control: AVCC0/AVSS0
      Input: Addition/Averaging Mask (channel availability varies by MCU and unit): 
      Input: Sample and Hold: Sample and Hold Channels (Available only on selected MCUs): 
      Input: Sample and Hold: Sample Hold States (Applies only to channels 0, 1, 2): 24
      Input: Window Compare: Window Mode: Enabled
      Input: Window Compare: Event Output: AND
      Input: Window Compare: Window A: Enable: Enabled
      Input: Window Compare: Window A: Channels to compare (channel availability varies by MCU and unit): Channel 0
      Input: Window Compare: Window A: Channel comparison mode (channel availability varies by MCU and unit): 
      Input: Window Compare: Window A: Lower Reference: 1888
      Input: Window Compare: Window A: Upper Reference: 2208
      Input: Window Compare: Window B: Enable: Enabled
      Input: Window Compare: Window B: Channel to compare (channel availability varies by MCU and unit): Channel 1
      Input: Window Compare: Window B: Comparison mode: Greater Than or Inside Window
      Input: Window Compare: Window B: Lower Reference: 0x000
      Input: Window Compare: Window B: Upper Reference: 0xFFF
      Interrupts: Callback: NULL
      Interrupts: Scan End Interrupt Priority: Disabled
      Interrupts: Scan End Group B Interrupt Priority: Disabled
      Interrupts: Window Compare A Interrupt Priority: Priority 2
      Interrupts: Window Compare B Interrupt Priority: Priority 2
      Extra: ADC Ring Buffer: Not Supported
      
    Instance "g_elc Event Link Controller (r_elc)"
      Name: g_elc
      
    Instance "g_timer_amic Timer, Low-Power (r_agt)"
      General: Name: g_timer_amic
      General: Counter Bit Width: AGT 16-bit
      General: Channel: 0
      General: Mode: Periodic
      General: Period: 16000
      General: Period Unit: Hertz
      Output: Duty Cycle Percent (only applicable in PWM mode): 50
      General: Count Source: PCLKB
      Output: AGTOA Output: Disabled
      Output: AGTOB Output: Disabled
      Output: AGTO Output: Disabled
      Input: Measurement Mode: Measure Disabled
      Input: Input Filter: No Filter
      Input: Enable Pin: Enable Pin Not Used
      Input: Trigger Edge: Trigger Edge Rising
      Interrupts: Callback: NULL
      Interrupts: Underflow Interrupt Priority: Disabled
      
    Instance "g_adc_amic ADC (r_adc)"
      General: Name: g_adc_amic
      General: Unit: 0
      General: Resolution: 12-Bit
      General: Alignment: Right
      General: Clear after read: On
      General: Mode: Single Scan
      General: Double-trigger: Disabled
      Input: Channel Scan Mask (channel availability varies by MCU): Channel 0
      Input: Group B Scan Mask (channel availability varies by MCU): 
      Interrupts: Normal/Group A Trigger: AGT0 INT (AGT interrupt)
      Interrupts: Group B Trigger: Disabled
      Interrupts: Group Priority (Valid only in Group Scan Mode): Group A cannot interrupt Group B
      Input: Add/Average Count: Disabled
      Input: Reference Voltage control: AVCC0/AVSS0
      Input: Addition/Averaging Mask (channel availability varies by MCU and unit): 
      Input: Sample and Hold: Sample and Hold Channels (Available only on selected MCUs): 
      Input: Sample and Hold: Sample Hold States (Applies only to channels 0, 1, 2): 24
      Input: Window Compare: Window Mode: Disabled
      Input: Window Compare: Event Output: OR
      Input: Window Compare: Window A: Enable: Disabled
      Input: Window Compare: Window A: Channels to compare (channel availability varies by MCU and unit): 
      Input: Window Compare: Window A: Channel comparison mode (channel availability varies by MCU and unit): 
      Input: Window Compare: Window A: Lower Reference: 0
      Input: Window Compare: Window A: Upper Reference: 0
      Input: Window Compare: Window B: Enable: Disabled
      Input: Window Compare: Window B: Channel to compare (channel availability varies by MCU and unit): Channel 0
      Input: Window Compare: Window B: Comparison mode: Less Than or Outside Window
      Input: Window Compare: Window B: Lower Reference: 0
      Input: Window Compare: Window B: Upper Reference: 0
      Interrupts: Callback: adc_dtc_end_cb
      Interrupts: Scan End Interrupt Priority: Priority 3
      Interrupts: Scan End Group B Interrupt Priority: Disabled
      Interrupts: Window Compare A Interrupt Priority: Disabled
      Interrupts: Window Compare B Interrupt Priority: Disabled
      Extra: ADC Ring Buffer: Not Supported
      
    Instance "g_adc_dtc_transfer Transfer (r_dtc) ADC0 SCAN END (End of A/D scanning operation)"
      Name: g_adc_dtc_transfer
      Mode: Normal
      Transfer Size: 2 Bytes
      Destination Address Mode: Incremented
      Source Address Mode: Fixed
      Repeat Area (Unused in Normal Mode): Source
      Interrupt Frequency: After all transfers have completed
      Number of Transfers: 480
      Number of Blocks (Valid only in Block Mode): 0
      Number of Transfer Descriptors: 1
      Activation Source: ADC0 SCAN END (End of A/D scanning operation)
      
    Instance "g_timer_sck Timer, General PWM (r_gpt)"
      General: Name: g_timer_sck
      General: Channel: 5
      General: Mode: Periodic
      General: Period: 1024000
      General: Compare Match: Compare Match A: Status: Disabled
      General: Compare Match: Compare Match A: Compare match value: 0
      General: Compare Match: Compare Match B: Status: Disabled
      General: Compare Match: Compare Match B: Compare match value: 0
      General: Compare Match: Compare Match C: Status: Disabled
      General: Compare Match: Compare Match C: Compare match value: 0x10000
      General: Compare Match: Compare Match D: Status: Disabled
      General: Compare Match: Compare Match D: Compare match value: 0x10000
      General: Compare Match: Compare Match E: Status: Disabled
      General: Compare Match: Compare Match E: Compare match value: 0x10000
      General: Compare Match: Compare Match F: Status: Disabled
      General: Compare Match: Compare Match F: Compare match value: 0x10000
      General: Period Unit: Hertz
      Output: Custom Waveform: GTIOA: Initial Output Level: Pin Level Low
      Output: Custom Waveform: GTIOA: Cycle End Output Level: Pin Level Retain
      Output: Custom Waveform: GTIOA: Compare Match Output Level: Pin Level Retain
      Output: Custom Waveform: GTIOA: Retain Output Level at Count Stop: Disabled
      Output: Custom Waveform: GTIOB: Initial Output Level: Pin Level Low
      Output: Custom Waveform: GTIOB: Cycle End Output Level: Pin Level Retain
      Output: Custom Waveform: GTIOB: Compare Match Output Level: Pin Level Retain
      Output: Custom Waveform: GTIOB: Retain Output Level at Count Stop: Disabled
      Output: Custom Waveform: Custom Waveform Enable: Disabled
      Output: Duty Cycle Percent (only applicable in PWM mode): 50
      Output: GTIOCA Output Enabled: False
      Output: GTIOCA Stop Level: Pin Level Low
      Output: GTIOCB Output Enabled: True
      Output: GTIOCB Stop Level: Pin Level Low
      Input: Count Up Source: 
      Input: Count Down Source: 
      Input: Start Source: 
      Input: Stop Source: 
      Input: Clear Source: 
      Input: Capture A Source: 
      Input: Capture B Source: 
      Input: Noise Filter A Sampling Clock Select: No Filter
      Input: Noise Filter B Sampling Clock Select: No Filter
      Pin Polarity: GTIOCnA Polarity: Normal
      Pin Polarity: GTIOCnB Polarity: Normal
      Interrupts: Callback: NULL
      Interrupts: Overflow/Crest Interrupt Priority: Disabled
      Interrupts: Capture/Compare match A Interrupt Priority: Disabled
      Interrupts: Capture/Compare match B Interrupt Priority: Disabled
      Interrupts: Compare Match C Interrupt Priority: Disabled
      Interrupts: Compare Match D Interrupt Priority: Disabled
      Interrupts: Compare Match E Interrupt Priority: Disabled
      Interrupts: Compare Match F Interrupt Priority: Disabled
      Interrupts: Underflow/Trough Interrupt Priority: Disabled
      Extra Features: Extra Features: Disabled
      Extra Features: Output Disable: POEG Link: POEG Channel 0
      Extra Features: Output Disable: Output Disable POEG Trigger: 
      Extra Features: ADC Trigger: Start Event Trigger (Channels with GTINTAD only): 
      Extra Features: ADC Trigger: ADC A Compare Match (Raw Counts): 0
      Extra Features: ADC Trigger: ADC B Compare Match (Raw Counts): 0
      Extra Features: Dead Time (Value range varies with Channel): Dead Time Count Up (Raw Counts): 0
      Extra Features: Dead Time (Value range varies with Channel): Dead Time Count Down (Raw Counts) (Channels with GTDVD only): 0
      Extra Features: Interrupt Skipping (Channels with GTITC only): Interrupt to Count: None
      Extra Features: Interrupt Skipping (Channels with GTITC only): Interrupt Skip Count: 0
      Extra Features: Interrupt Skipping (Channels with GTITC only): Skip ADC Events: None
      Extra Features: Output Disable: GTIOCA Disable Setting: Disable Prohibited
      Extra Features: Output Disable: GTIOCB Disable Setting: Disable Prohibited
      
    Instance "g_timer_ws Timer, General PWM (r_gpt)"
      General: Name: g_timer_ws
      General: Channel: 6
      General: Mode: Saw-wave PWM
      General: Period: 32
      General: Compare Match: Compare Match A: Status: Disabled
      General: Compare Match: Compare Match A: Compare match value: 0
      General: Compare Match: Compare Match B: Status: Disabled
      General: Compare Match: Compare Match B: Compare match value: 0
      General: Compare Match: Compare Match C: Status: Disabled
      General: Compare Match: Compare Match C: Compare match value: 0x10000
      General: Compare Match: Compare Match D: Status: Disabled
      General: Compare Match: Compare Match D: Compare match value: 0x10000
      General: Compare Match: Compare Match E: Status: Disabled
      General: Compare Match: Compare Match E: Compare match value: 0x10000
      General: Compare Match: Compare Match F: Status: Disabled
      General: Compare Match: Compare Match F: Compare match value: 0x10000
      General: Period Unit: Raw Counts
      Output: Custom Waveform: GTIOA: Initial Output Level: Pin Level Low
      Output: Custom Waveform: GTIOA: Cycle End Output Level: Pin Level Retain
      Output: Custom Waveform: GTIOA: Compare Match Output Level: Pin Level Retain
      Output: Custom Waveform: GTIOA: Retain Output Level at Count Stop: Disabled
      Output: Custom Waveform: GTIOB: Initial Output Level: Pin Level High
      Output: Custom Waveform: GTIOB: Cycle End Output Level: Pin Level Retain
      Output: Custom Waveform: GTIOB: Compare Match Output Level: Pin Level Toggle
      Output: Custom Waveform: GTIOB: Retain Output Level at Count Stop: Disabled
      Output: Custom Waveform: Custom Waveform Enable: Enabled
      Output: Duty Cycle Percent (only applicable in PWM mode): 50
      Output: GTIOCA Output Enabled: False
      Output: GTIOCA Stop Level: Pin Level Low
      Output: GTIOCB Output Enabled: True
      Output: GTIOCB Stop Level: Pin Level Low
      Input: Count Up Source: GTETRGB Falling Edge
      Input: Count Down Source: 
      Input: Start Source: 
      Input: Stop Source: 
      Input: Clear Source: 
      Input: Capture A Source: 
      Input: Capture B Source: 
      Input: Noise Filter A Sampling Clock Select: No Filter
      Input: Noise Filter B Sampling Clock Select: No Filter
      Pin Polarity: GTIOCnA Polarity: Normal
      Pin Polarity: GTIOCnB Polarity: Normal
      Interrupts: Callback: NULL
      Interrupts: Overflow/Crest Interrupt Priority: Disabled
      Interrupts: Capture/Compare match A Interrupt Priority: Disabled
      Interrupts: Capture/Compare match B Interrupt Priority: Disabled
      Interrupts: Compare Match C Interrupt Priority: Disabled
      Interrupts: Compare Match D Interrupt Priority: Disabled
      Interrupts: Compare Match E Interrupt Priority: Disabled
      Interrupts: Compare Match F Interrupt Priority: Disabled
      Interrupts: Underflow/Trough Interrupt Priority: Disabled
      Extra Features: Extra Features: Disabled
      Extra Features: Output Disable: POEG Link: POEG Channel 0
      Extra Features: Output Disable: Output Disable POEG Trigger: 
      Extra Features: ADC Trigger: Start Event Trigger (Channels with GTINTAD only): 
      Extra Features: ADC Trigger: ADC A Compare Match (Raw Counts): 0
      Extra Features: ADC Trigger: ADC B Compare Match (Raw Counts): 0
      Extra Features: Dead Time (Value range varies with Channel): Dead Time Count Up (Raw Counts): 0
      Extra Features: Dead Time (Value range varies with Channel): Dead Time Count Down (Raw Counts) (Channels with GTDVD only): 0
      Extra Features: Interrupt Skipping (Channels with GTITC only): Interrupt to Count: None
      Extra Features: Interrupt Skipping (Channels with GTITC only): Interrupt Skip Count: 0
      Extra Features: Interrupt Skipping (Channels with GTITC only): Skip ADC Events: None
      Extra Features: Output Disable: GTIOCA Disable Setting: Disable Prohibited
      Extra Features: Output Disable: GTIOCB Disable Setting: Disable Prohibited
      
    Instance "g_spi_i2s SPI (r_spi)"
      Name: g_spi_i2s
      Channel: 0
      Receive Interrupt Priority: Priority 1
      Transmit Buffer Empty Interrupt Priority: Priority 1
      Transfer Complete Interrupt Priority: Priority 1
      Error Interrupt Priority: Priority 1
      Operating Mode: Slave
      Clock Phase: Data sampling on even edge, data variation on odd edge
      Clock Polarity: Low when idle
      Mode Fault Error: Disable
      Bit Order: MSB First
      Callback: g_spi_cb
      SPI Mode: SPI Operation
      SPI burst transfer without delay between frames: Disable
      Full or Transmit Only Mode: Full Duplex
      Slave Select Polarity: Active Low
      Select SSL(Slave Select): SSL0
      MOSI Idle State: MOSI Idle Value Fixing Disable
      Parity Mode: Disabled
      Byte Swapping: Disable
      Bitrate: 16000000
      Clock Delay: 1 Clock
      SSL Negation Delay: 1 Clock
      Next Access Delay: 1 Clock
      
      Instance "g_transfer0 Transfer (r_dtc) SPI0 TXI (Transmit buffer empty)"
        Name: g_transfer0
        Mode: Normal
        Transfer Size: 2 Bytes
        Destination Address Mode: Fixed
        Source Address Mode: Incremented
        Repeat Area (Unused in Normal Mode): Source
        Interrupt Frequency: After all transfers have completed
        Number of Transfers: 0
        Number of Blocks (Valid only in Block Mode): 0
        Number of Transfer Descriptors: 1
        Activation Source: SPI0 TXI (Transmit buffer empty)
        
      Instance "g_transfer1 Transfer (r_dtc) SPI0 RXI (Receive buffer full)"
        Name: g_transfer1
        Mode: Normal
        Transfer Size: 2 Bytes
        Destination Address Mode: Incremented
        Source Address Mode: Fixed
        Repeat Area (Unused in Normal Mode): Destination
        Interrupt Frequency: After all transfers have completed
        Number of Transfers: 0
        Number of Blocks (Valid only in Block Mode): 0
        Number of Transfer Descriptors: 1
        Activation Source: SPI0 RXI (Receive buffer full)
        
    Instance "g_poeg_ws Port Output Enable for GPT (r_poeg)"
      General: Name: g_poeg_ws
      General: Channel: 1
      General: Trigger: GTETRG Pin
      Input: GTETRG Polarity: Active High
      Input: GTETRG Noise Filter: Disabled
      Interrupts: Callback: NULL
      Interrupts: Interrupt Priority: Disabled
      
    Instance "g_timer_ssl Timer, General PWM (r_gpt)"
      General: Name: g_timer_ssl
      General: Channel: 3
      General: Mode: Saw-wave PWM
      General: Period: 32
      General: Compare Match: Compare Match A: Status: Disabled
      General: Compare Match: Compare Match A: Compare match value: 0
      General: Compare Match: Compare Match B: Status: Disabled
      General: Compare Match: Compare Match B: Compare match value: 0
      General: Compare Match: Compare Match C: Status: Disabled
      General: Compare Match: Compare Match C: Compare match value: 0x10000
      General: Compare Match: Compare Match D: Status: Disabled
      General: Compare Match: Compare Match D: Compare match value: 0x10000
      General: Compare Match: Compare Match E: Status: Disabled
      General: Compare Match: Compare Match E: Compare match value: 0x10000
      General: Compare Match: Compare Match F: Status: Disabled
      General: Compare Match: Compare Match F: Compare match value: 0x10000
      General: Period Unit: Raw Counts
      Output: Custom Waveform: GTIOA: Initial Output Level: Pin Level Low
      Output: Custom Waveform: GTIOA: Cycle End Output Level: Pin Level Retain
      Output: Custom Waveform: GTIOA: Compare Match Output Level: Pin Level Retain
      Output: Custom Waveform: GTIOA: Retain Output Level at Count Stop: Disabled
      Output: Custom Waveform: GTIOB: Initial Output Level: Pin Level High
      Output: Custom Waveform: GTIOB: Cycle End Output Level: Pin Level Retain
      Output: Custom Waveform: GTIOB: Compare Match Output Level: Pin Level Toggle
      Output: Custom Waveform: GTIOB: Retain Output Level at Count Stop: Disabled
      Output: Custom Waveform: Custom Waveform Enable: Enabled
      Output: Duty Cycle Percent (only applicable in PWM mode): 50
      Output: GTIOCA Output Enabled: False
      Output: GTIOCA Stop Level: Pin Level Low
      Output: GTIOCB Output Enabled: True
      Output: GTIOCB Stop Level: Pin Level Low
      Input: Count Up Source: GTETRGB Falling Edge
      Input: Count Down Source: 
      Input: Start Source: 
      Input: Stop Source: 
      Input: Clear Source: 
      Input: Capture A Source: 
      Input: Capture B Source: 
      Input: Noise Filter A Sampling Clock Select: No Filter
      Input: Noise Filter B Sampling Clock Select: No Filter
      Pin Polarity: GTIOCnA Polarity: Normal
      Pin Polarity: GTIOCnB Polarity: Normal
      Interrupts: Callback: NULL
      Interrupts: Overflow/Crest Interrupt Priority: Disabled
      Interrupts: Capture/Compare match A Interrupt Priority: Disabled
      Interrupts: Capture/Compare match B Interrupt Priority: Disabled
      Interrupts: Compare Match C Interrupt Priority: Disabled
      Interrupts: Compare Match D Interrupt Priority: Disabled
      Interrupts: Compare Match E Interrupt Priority: Disabled
      Interrupts: Compare Match F Interrupt Priority: Disabled
      Interrupts: Underflow/Trough Interrupt Priority: Disabled
      Extra Features: Extra Features: Disabled
      Extra Features: Output Disable: POEG Link: POEG Channel 0
      Extra Features: Output Disable: Output Disable POEG Trigger: 
      Extra Features: ADC Trigger: Start Event Trigger (Channels with GTINTAD only): 
      Extra Features: ADC Trigger: ADC A Compare Match (Raw Counts): 0
      Extra Features: ADC Trigger: ADC B Compare Match (Raw Counts): 0
      Extra Features: Dead Time (Value range varies with Channel): Dead Time Count Up (Raw Counts): 0
      Extra Features: Dead Time (Value range varies with Channel): Dead Time Count Down (Raw Counts) (Channels with GTDVD only): 0
      Extra Features: Interrupt Skipping (Channels with GTITC only): Interrupt to Count: None
      Extra Features: Interrupt Skipping (Channels with GTITC only): Interrupt Skip Count: 0
      Extra Features: Interrupt Skipping (Channels with GTITC only): Skip ADC Events: None
      Extra Features: Output Disable: GTIOCA Disable Setting: Disable Prohibited
      Extra Features: Output Disable: GTIOCB Disable Setting: Disable Prohibited
      
    Instance "g_flash0 Flash (r_flash_lp)"
      Name: g_flash0
      Data Flash Background Operation: Enabled
      Callback: flash0_bgo_callback
      Flash Ready Interrupt Priority: Priority 2
      
    Instance "g_uart_ds UART (r_sci_uart)"
      General: Name: g_uart_ds
      General: Channel: 3
      General: Data Bits: 8bits
      General: Parity: None
      General: Stop Bits: 1bit
      Baud: Baud Rate: 460800
      Baud: Baud Rate Modulation: Enabled
      Baud: Max Error (%): 5
      Flow Control: CTS/RTS Selection: Hardware RTS
      Flow Control: Software RTS Port: Disabled
      Flow Control: Software RTS Pin: Disabled
      Extra: Clock Source: Internal Clock
      Extra: Start bit detection: Falling Edge
      Extra: Noise Filter: Disable
      Extra: Receive FIFO Trigger Level: Max
      Extra: IrDA: Enable: Disabled
      Extra: IrDA: RXD Polarity Switching: Normal
      Extra: IrDA: TXD Polarity Switching: Normal
      Extra: RS-485: DE Pin: Disable
      Extra: RS-485: DE Pin Polarity: Active High
      Extra: RS-485: DE Port Number: Disabled
      Extra: RS-485: DE Pin Number: Disabled
      Interrupts: Callback: user_uart_callback
      Interrupts: Receive Interrupt Priority: Priority 2
      Interrupts: Transmit Data Empty Interrupt Priority: Priority 2
      Interrupts: Transmit End Interrupt Priority: Priority 2
      Interrupts: Error Interrupt Priority: Priority 2
      
    Instance "g_dac_playback DAC (r_dac)"
      Name: g_dac_playback
      Channel: 0
      Synchronize with ADC: Disabled
      Data Format: Right Justified
      Output Amplifier: Not Supported
      Charge Pump (Requires MOCO active): Not Supported
      Internal Output: Not Supported
      ELC Trigger Source: Disabled
      Reference Voltage: AVCC0/AVSS0
      
    Instance "g_timer_playback Timer, General PWM (r_gpt)"
      General: Name: g_timer_playback
      General: Channel: 0
      General: Mode: Periodic
      General: Period: 16000
      General: Compare Match: Compare Match A: Status: Disabled
      General: Compare Match: Compare Match A: Compare match value: 0
      General: Compare Match: Compare Match B: Status: Disabled
      General: Compare Match: Compare Match B: Compare match value: 0
      General: Compare Match: Compare Match C: Status: Disabled
      General: Compare Match: Compare Match C: Compare match value: 0x10000
      General: Compare Match: Compare Match D: Status: Disabled
      General: Compare Match: Compare Match D: Compare match value: 0x10000
      General: Compare Match: Compare Match E: Status: Disabled
      General: Compare Match: Compare Match E: Compare match value: 0x10000
      General: Compare Match: Compare Match F: Status: Disabled
      General: Compare Match: Compare Match F: Compare match value: 0x10000
      General: Period Unit: Hertz
      Output: Custom Waveform: GTIOA: Initial Output Level: Pin Level Low
      Output: Custom Waveform: GTIOA: Cycle End Output Level: Pin Level Retain
      Output: Custom Waveform: GTIOA: Compare Match Output Level: Pin Level Retain
      Output: Custom Waveform: GTIOA: Retain Output Level at Count Stop: Disabled
      Output: Custom Waveform: GTIOB: Initial Output Level: Pin Level Low
      Output: Custom Waveform: GTIOB: Cycle End Output Level: Pin Level Retain
      Output: Custom Waveform: GTIOB: Compare Match Output Level: Pin Level Retain
      Output: Custom Waveform: GTIOB: Retain Output Level at Count Stop: Disabled
      Output: Custom Waveform: Custom Waveform Enable: Disabled
      Output: Duty Cycle Percent (only applicable in PWM mode): 50
      Output: GTIOCA Output Enabled: False
      Output: GTIOCA Stop Level: Pin Level Low
      Output: GTIOCB Output Enabled: False
      Output: GTIOCB Stop Level: Pin Level Low
      Input: Count Up Source: 
      Input: Count Down Source: 
      Input: Start Source: 
      Input: Stop Source: 
      Input: Clear Source: 
      Input: Capture A Source: 
      Input: Capture B Source: 
      Input: Noise Filter A Sampling Clock Select: No Filter
      Input: Noise Filter B Sampling Clock Select: No Filter
      Pin Polarity: GTIOCnA Polarity: Normal
      Pin Polarity: GTIOCnB Polarity: Normal
      Interrupts: Callback: g_timer_playback_callback
      Interrupts: Overflow/Crest Interrupt Priority: Priority 2
      Interrupts: Capture/Compare match A Interrupt Priority: Disabled
      Interrupts: Capture/Compare match B Interrupt Priority: Disabled
      Interrupts: Compare Match C Interrupt Priority: Disabled
      Interrupts: Compare Match D Interrupt Priority: Disabled
      Interrupts: Compare Match E Interrupt Priority: Disabled
      Interrupts: Compare Match F Interrupt Priority: Disabled
      Interrupts: Underflow/Trough Interrupt Priority: Disabled
      Extra Features: Extra Features: Disabled
      Extra Features: Output Disable: POEG Link: POEG Channel 0
      Extra Features: Output Disable: Output Disable POEG Trigger: 
      Extra Features: ADC Trigger: Start Event Trigger (Channels with GTINTAD only): 
      Extra Features: ADC Trigger: ADC A Compare Match (Raw Counts): 0
      Extra Features: ADC Trigger: ADC B Compare Match (Raw Counts): 0
      Extra Features: Dead Time (Value range varies with Channel): Dead Time Count Up (Raw Counts): 0
      Extra Features: Dead Time (Value range varies with Channel): Dead Time Count Down (Raw Counts) (Channels with GTDVD only): 0
      Extra Features: Interrupt Skipping (Channels with GTITC only): Interrupt to Count: None
      Extra Features: Interrupt Skipping (Channels with GTITC only): Interrupt Skip Count: 0
      Extra Features: Interrupt Skipping (Channels with GTITC only): Skip ADC Events: None
      Extra Features: Output Disable: GTIOCA Disable Setting: Disable Prohibited
      Extra Features: Output Disable: GTIOCB Disable Setting: Disable Prohibited
      
