Board Support Package. Device-specific system configuration default values. More...

#include "boards/brd_io_config_ra6w1.h"

Macros
#define	dg_configRC32K_FREQ
	Vaule of the RC32K oscilator frequency in Hz.

#define	dg_configLP_CLK_DRIFT
	Acceptable clock tick drift (in parts per million) for the Low-power clock.

#define	dg_configXTAL32K_SETTLE_TIME
	Time needed for the settling of the LP clock, in msec.

#define	dg_configXTAL40M_SETTLE_TIME_IN_USEC
	XTAL40M settle time. More...

#define	dg_configENABLE_XTAL40M_ON_WAKEUP
	Enable XTAL40M upon system wake-up. More...

#define	dg_configVOLTAGE_CHECK_LP_CYCLES
	The number of LP clock cycles required to check the voltage of an LDO during startup.

#define	dg_configHW_FSM_WAKEUP_CYCLES
	The number of LP clock cycles required for the HW FSM to detect the wake-up signal.

#define	dg_configSYSTEM_STARTUP_CYCLES
	The number of LP clock cycles required for the system to start-up.

#define	dg_configWAKEUP_RC32_TIME_SLOW
	RC32 wake-up time in slow wake-up mode. More...

#define	dg_configWAKEUP_RC32_TIME_FAST
	RC32 wake-up time in fast wake-up mode. More...

#define	dg_configWAKEUP_RC32_TIME_ULTRA_FAST
	RC32 wake-up time. More...

#define	dg_configDEFAULT_CLK_FREQ_TRIM_REG__XTAL32M_TRIM__VALUE
	XTAL32M trimming default settings.

#define	dg_configWDOG_IDLE_RESET_VALUE
	Reset value for Watchdog when system is idle.

#define	dg_configWDOG_MAX_TASKS_CNT
	Maximum watchdog tasks. More...

#define	dg_configWDOG_EXT
	Extend maximum watchdog tasks. More...

#define	dg_configPOWER_1V8_ACTIVE
	When set to 1, the 1V8 rail is powered, when the system is in active state. When set to 2 the rail configuration will be defined by the application.

#define	dg_configPOWER_1V8_SLEEP
	When set to 1, the 1V8 is powered during sleep. When set to 2 the rail configuration will be defined by the application.

#define	dg_configPOWER_1V8P_ACTIVE
	When set to 1, the 1V8P rail is powered. More...

#define	dg_configPOWER_1V8P_SLEEP
	When set to 1, the 1V8P is powered during sleep. When set to 2 the rail configuration will be defined by the application.

#define	dg_configFLASH_POWER_OFF
	When set to 1, the Flash is powered off during sleep.

#define	dg_configQSPIC2_DEV_AUTODETECT
	Enable the Auto-detection mode for QSPIC2 device. More...

#define	dg_configQSPIC2_DEV_HEADER_FILE
	The QSPI 2 Driver header file to include. More...

#define	dg_configQSPIC2_DEV_CONFIG
	The QSPI 2 Driver configuration structure. More...

#define	dg_configFLASH_HEADER_FILE
	The Flash Driver header file to include. More...

#define	dg_configFLASH_CONFIG
	The Flash Driver configuration structure. More...

#define	dg_configFLASH_CONFIG_VERIFY
	Flash device configuration verification. More...

#define	dg_configUSE_SOC
	When set to 1, State of Charge function is enabled.

#define	dg_configUART3_SOFTWARE_FIFO_SIZE
	UART3's software FIFO size.

#define	dg_configUART3_RX_CIRCULAR_DMA_BUF_SIZE
	UART3's Circular DMA buffer size for RX.

#define	dg_configUSE_BOARD
	Set the board that is used.

Detailed Description

Board Support Package. Device-specific system configuration default values.

This software ("Software") is owned by Renesas Electronics.

By using this Software you agree that Renesas Electronics retains all intellectual property and proprietary rights in and to this Software and any use, reproduction, disclosure or distribution of the Software without express written permission or a license agreement from Renesas Electronics is strictly prohibited. This Software is solely for use on or in conjunction with Renesas Electronics products.

EXCEPT AS OTHERWISE PROVIDED IN A LICENSE AGREEMENT BETWEEN THE PARTIES, THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. EXCEPT AS OTHERWISE PROVIDED IN A LICENSE AGREEMENT BETWEEN THE PARTIES, IN NO EVENT SHALL RENESAS ELECTRONICS BE LIABLE FOR ANY DIRECT, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE SOFTWARE.

Macros

Detailed Description