|
SmartSnippets DA1459x SDK
|
Board Support Package. Device-specific system configuration default values. More...
#include "boards/brd_prodk_da1459x.h"Go to the source code of this file.
Macros | |
| #define | dg_configRC32K_FREQ (32000) |
| Value of the RC32K oscillator frequency in Hz. More... | |
| #define | dg_configLP_CLK_DRIFT (500) |
| Acceptable clock tick drift (in parts per million) for the Low-power clock. More... | |
| #define | dg_configXTAL32K_SETTLE_TIME (8000) |
| Time needed for the settling of the LP clock, in msec. More... | |
| #define | dg_configXTAL32M_SETTLE_TIME_IN_USEC (0x0) |
| XTAL32M maximum expected settling time. More... | |
| #define | dg_configENABLE_XTAL32M_ON_WAKEUP (1) |
| Enable XTAL32M upon system wake-up. More... | |
| #define | dg_configWAKEUP_NORMAL (300) |
| The time in us needed to wake-up in normal wake-up mode. More... | |
| #define | dg_configWAKEUP_FAST (12) |
| The time in us needed to wake up in fast wake up mode. More... | |
| #define | dg_configDEFAULT_CLK_RC32M_REG_RC32M_BIAS__VALUE (0xD) |
| RC32M trimming default settings. | |
| #define | dg_configDEFAULT_XTAL32M_TRIM_REG__XTAL32M_TRIM__VALUE (0x45) |
| XTAL32M trimming default settings. | |
| #define | dg_configWDOG_IDLE_RESET_VALUE (SYS_WDOG_WATCHDOG_REG_WDOG_VAL_Msk >> SYS_WDOG_WATCHDOG_REG_WDOG_VAL_Pos) |
| Reset value for Watchdog when system is idle. | |
| #define | dg_configWDOG_MAX_TASKS_CNT (8) |
| Maximum watchdog tasks. More... | |
| #define | dg_configWDOG_GUARD_IDLE_TASK (1) |
| Watchdog guards the idle-task in OS applications. More... | |
| #define | dg_configREDUCE_RETAINED_CODE (1) |
| System debug logging protection mechanism. More... | |
| #define | dg_configPOWER_1V8_ACTIVE (2) |
| The rail from which the external Flash is powered, if an external Flash is used. More... | |
| #define | dg_configPOWER_1V8_SLEEP (2) |
| When set to 1, the 1V8 is powered during sleep. When set to 2 the rail configuration will be defined by the application. More... | |
| #define | dg_configQSPI_FLASH_POWER_DOWN (1) |
| When set to 1, the system activates the QSPI flash power-down mode when it enters sleep in order to minimize overall power consumption. More... | |
| #define | dg_configQSPI_DRIVE_CURRENT (HW_QSPI_DRIVE_CURRENT_4) |
| Set the Drive Strength of the QSPI Controller. More... | |
| #define | dg_configQSPI_SLEW_RATE (HW_QSPI_SLEW_RATE_0) |
| Set the Slew Rate of the QSPI Controller. More... | |
| #define | dgconfigQSPI_ERASE_IN_AUTOMODE (1) |
| Select whether the QSPI Flash memory will be erased in Auto or in Manual Access Mode. More... | |
| #define | dg_configQSPI_FLASH_HEADER_FILE "qspi_mx25u3235_v2.h" |
| The Flash Driver header file to include. More... | |
| #define | dg_configQSPI_FLASH_CONFIG qspi_mx25u3235_cfg |
| The Flash Driver configuration structure. More... | |
| #define | dg_configQSPI_FLASH_CONFIG_VERIFY (0) |
| Flash device configuration verification. More... | |
| #define | dg_configEFLASH_MASS_ERASE_TIME 160000 |
| EFLASH memory mass erase time in usec. More... | |
| #define | dg_configEFLASH_PAGE_ERASE_TIME 160000 |
| EFLASH memory page erase time in usec. More... | |
| #define | dg_configEFLASH_WORD_WRITE_TIME 16 |
| EFLASH memory one word write time in usec. More... | |
| #define | dg_configHW_FCU_WAIT_CYCLES_MODE (2) |
| Activate EFLASH optimum wait cycle functionality. More... | |
| #define | dg_configUSE_SOC (0) |
| When set to 1, State of Charge function is enabled. More... | |
| #define | dg_configIVT_PROTECT_REGION MPU_REGION_7 |
| MPU region for IVT protection. More... | |
| #define | dg_configUSE_BOARD |
| Set the board that is used. | |
Board Support Package. Device-specific system configuration default values.
Copyright (C) 2020-2023 Renesas Electronics Corporation and/or its affiliates. All rights reserved. Confidential Information.
This software ("Software") is supplied by Renesas Electronics Corporation and/or its affiliates ("Renesas"). Renesas grants you a personal, non-exclusive, non-transferable, revocable, non-sub-licensable right and license to use the Software, solely if used in or together with Renesas products. You may make copies of this Software, provided this copyright notice and disclaimer ("Notice") is included in all such copies. Renesas reserves the right to change or discontinue the Software at any time without notice.
THE SOFTWARE IS PROVIDED "AS IS". RENESAS DISCLAIMS ALL WARRANTIES OF ANY KIND, WHETHER EXPRESS, IMPLIED, OR STATUTORY, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. TO THE MAXIMUM EXTENT PERMITTED UNDER LAW, IN NO EVENT SHALL RENESAS BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE, EVEN IF RENESAS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. USE OF THIS SOFTWARE MAY BE SUBJECT TO TERMS AND CONDITIONS CONTAINED IN AN ADDITIONAL AGREEMENT BETWEEN YOU AND RENESAS. IN CASE OF CONFLICT BETWEEN THE TERMS OF THIS NOTICE AND ANY SUCH ADDITIONAL LICENSE AGREEMENT, THE TERMS OF THE AGREEMENT SHALL TAKE PRECEDENCE. BY CONTINUING TO USE THIS SOFTWARE, YOU AGREE TO THE TERMS OF THIS NOTICE.IF YOU DO NOT AGREE TO THESE TERMS, YOU ARE NOT PERMITTED TO USE THIS SOFTWARE.
1.8.16